Slideshow

Bari Mando Finish

Luthiery work

Mandolins
Quatuor
- » Baroque Violin pegs
- » Pochette Jacques Du Mesnil
- » Viola Charles IX
Woodwinds
- » Diatonic clarinet
- » Chalumeau
- » Irish Whistle
- » Breton flute
- » Breton bombards
- Techniques
  - » Bone Mount
  - » Long holes boring
  - » Making a key
  - » Pewter inlaying
  - » Conical reamers
Percussions
- » Practice set for the scottish snare drum
- » Cajòn
Miscellaneous
- » Making of a wooden case for Ukulele
Workshop
- » Enhanced Clamps
- » A two-handed gouge
- » Convert inches into millimeters
- » Finger planes
- » Instrument making vise
- » My Metric String action gauge
- » Purfling chisel
- » Purfling cutter
- » Radius sanding block
- » Resawing on the bandsaw
- » Soft vise jaws for the luthier
- » Thickness Gauge
- » Thickness Punch
- » Thickness sander
- » Toothed blades

Woodworking

Vintage furnitures restoration
Works
- » Plancha Trolley
- » Some works
- » Stool
Finishing recipes
- » Ebonizing
Wood knowledge
- » Wood and moisture
Workshop
- » Bandsaw blade tension
- » Carving platform
- » Centering calipers
- » Cordless drill to corded
- » Disk Sander
- » Manual feeder blocks for table saw
- » My branding mark
- » Push Sticks
- » Router plane
- » Scartch Stock
- » Scraping plane
- » Silver soldering a bandsaw blade
- » Spokeshave
- » Startup and blade tension
- » Tenon saw
- » Tenoning Jig

Woodturning

My Woodturnings
- » Jewellery
- » Bowls
- » Miscellaneous
- » Pencils
- » Spinning tops
- » Lamps
Woodturning shop
- » My tools
- » Telescopic hollowing tool
- » Transverse drilling on the lathe

Leather work

Works
- » Bracelet Aile ou la Cuisse
- » HDD leather case
- » Kitchen Knife Leather Roll
- » Leather Apron
- » Leather belt pouch
- » Miscellaneous
- » Phone Case N°1
- » Phone Case N°2
- » Steampunk watch
Technique
- » Breading
- » Lacing
Tooling
- » Diamond shaped awl
- » Edge burnishers
- » Leather Stitching Clamp

Metal working

Metal working
- » Wood and Metal Rings
Tooling
- » Engraver bowl vice
- » Grinding an ER32 collet chuck
- » Metal Engraving tools

Softwares

FOR THE LUTHIER
- » Frequency <=> Note
- » Inch <=> mm
- » Fretboard Design
The softwares that I use
- » Bigprint
- » Qcad
- » Photofiltre
- » Audacity
- » Melody Assistant
Android in the workshop
Some tricks

Webmaster - Infos

Recommend

Text version

Contact Me

To contact me

Visits

visitors

Purfling chisel

This article is available in the standard RSS format for publication on your website :
http://www.labellenote.fr/data/en-articles.xml

Purfling chisel

Here is a simple way to make a little chisel that aim at carving a groove for purfling inlaying.

The blade is made out of a carbon steel jigsaw blade ground in the shape of a hook and has the same width as the purfling (1.3mm). The sharperning is finished on a stone.

The handle is made out of a section of round ash, with a groove cut at the tip on the bandsaw. The bottom of the groove has the same tilt as the blade.

The blades can be changed, in order to adapt to any situation. The blade is tightened in place thanks to a little bolt, as shown on the picture :

Here, the chisel in action. The edges of the groove will have been first traced with the purfling cutter, and deepened with a luthier knife.

The shape of the chisel shown here is interesting for the biggest curves or straight lines, it removes the wood across the full width of the groove.

The shape of the chisel below is better suited for the tight curves. The cutting part is shorter and the foot is narrower. The width has been reduced also to less than 1 mm, in order to follow the curve more easily.

Christophe

Associated keywords

Unless explicitly specified, all works presented on this page are released under a
Creative Commons BY-NC-SA International License.
Licence Creative Commons
Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License