By continuing your navigation on this site, you accept the use of cookies to offer you contents and adapted services. Legal Notice.
You are here :   Welcome » Edge burnishers
 

Slideshow

Luthiery work

 ↑  

Woodworking

Woodturning

 ↑  

Softwares

Search
 
Close

Contact Me

Visits

   visitors

   visitors online

Find La Belle Note on FacebookJoin me on HomemadeTools.net

Edge burnishers

rss This article is available in the standard RSS format for publication on your website :
http://www.labellenote.fr/data/en-articles.xml

    Edge Burnisher   

FB

The burnisher is a necessary tool for finishing edges in leather work. There are many videos on the Net showing this operation, I show you here how you can make three different versions of this tool if you have access to a lathe.

Manual burnisher

This first version is very simple, it is used by hand rubbing back and forth, quickly enough, so as to heat-up the edge and the resin or wax that covers it.

EdgeBurnisher_0000.jpg

Hand burnisher.

This tool is most often made of beech, but one can also use a naturally siliceous wood such as iroko for example, which will give it a slightly abrasive power and which will heat a little more efficiently.
  All parts of the tool can be used. The curved head for crushing pieces in full leather for example, the three grooves of three different thicknesses for the edges, and the conical part for flat or closed parts.

Mechanical burnisher for Dremel

EdgeBurnisher_0011.jpg

Dremel burnisher for small parts.

This burnisher has a 3.2 mm shaft that mounts into a Dremel-type high-speed spinning tool chuck.
This tool is well adapted to small parts, when the contour has curvatures with tight radius.
Dremel type tools are limited torque tools, so we can not push very hard on the work. The tool can, however, be used with a flexible shaft connected to a drill press or lathe for example.

×
- 1 -
 

20mm ebony blank, center drilled at 3.2 mm

- 2 -
 

The axis of 3.2 mm is glued with epoxy.

- 3 -
 

The forms are well rounded, a sharp angle would mark the leather.

- 4 -
 

Do not press too much to keep a high speed.

- 5 -
 

The result should be soft and the edge glossy.

Large mechanical burnisher

EdgeBurnisher_0010.jpg

Dremel burnisher for small parts.

Here is a version of the large diameter burnisher, mounted on a 6mm axis, intended to be used on a drill press.
This burnisher can handle larger parts and in a more intensive way.

- 1 -
 

Roughing out an ash blank of 60mm diameter. 6mm axis glued with epoxy.

- 2 -
 

3 widths of grooves

- 3 -
 

Assembly in the drill press.

- 4 -
 

Preparation of the edge, after sanding, with gum Arabic.

- 5 -
 

Application of gum Arabic.

- 6 -
 

burnishing

- 7 -
 

The top can be used flat to soften the underside of a strap for example.

I recall that I do not sell these objects, I can however help you to make them if necessary.

Do not hesitate to react to this article in case of question or you can contact me
also on my Facebook page.
Good work !

Christophe

Associated keywords



Unless explicitly specified, all works presented on this page are released under a
Creative Commons BY-NC-SA International License.
Licence Creative Commons
Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License




Creation date : 19/11/2018 : 19:04
Category : Leather work - Tooling
Page read 286 times


Reactions to this article


Nobody gave a comment yet.
Be the first to do so!

Newsletter

To receive news about this website, consider subscribing to our Newsletter.

Contact Me

Visits

   visitors

   visitors online